Solution about "the network BIOS command limit has been reached " error

I am using Windows 8.1  .  While I am trying to open " http://www.wbgdrb.applythrunet.co.in/ " site , above error occurs and it asked me to go to microsoft knowledge base article 810886 which says - 

This issue may occur if the following conditions are true:
  • This issue may occur if the client computer submits simultaneous, long-term requests against a file server that uses the Server Message Block (SMB) protocol. An example of a long-term request is when a client computer uses the FindFirstChangeNotification function to monitor a server share for changes.
  • This issue may occur if the
    MaxCmds
    registry value setting on the client is less than 50, or the
    MaxMpxCt
    registry value setting on the server is less than 50.

    Note The
    MaxMpxCt
    registry value setting may have a different name on other SMB/CIFS implementations. The Common Internet File System (CIFS) specification refers to it as
    MaxMpxCount
    .

Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:

322756 How to back up and restore the registry in Windows



To resolve this issue, verify that the

MaxCmds
and
MaxMpxCt
registry values are set to 50 or more. To do this, follow these steps:

  1. Click Start, click Run, type regedit, and then click OK.
  2. Locate and then click the following key in the registry:
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\lanmanworkstation\parameters
  3. In the right pane, double-click the MaxCmds value.
  4. In the Value data box, verify that the value is 50 or more.

    Note In a Microsoft Windows Terminal Services environment, you may have to set the
    MaxCmds
    registry value to 500 or more. For more information, click the following article number to view the article in the Microsoft Knowledge Base:
    232476 Terminal Server client connections and logon limited by MaxWorkItem and MaxMpxCt values
  5. Locate and then click the following key in the registry:
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\lanmanserver\parameters
    Note Make sure that you make this change to the
    lanmanserver\parameters
    registry key and not to the
    lanmanworkstation\parameters
    registry key mentioned in step 2.
  6. In the right-pane, double-click the MaxMpxCt value.

    Note On SMB servers that are running a version of Windows earlier than Windows 2000, the
    MaxMpxCt
    registry entry is named
    MaxMpxCount
    , but has the same function.
  7. In the Value data box, verify that the value is 50 or more. 

    Note The
    MaxMpxCt
    value determines the maximum number of simultaneous, active requests that the server permits from an individual client.
  8. Quit Registry Editor.
  9. Restart the server.

Note The MaxCmds and MaxMpxCt registry entries are REG_DWORD decimal entries. If they do not exist on your computer, you can create them as new REG_DWORD values. The range of values for these registry entries is between 0 and 65535.

But I can"t find MaxCmds and MaxMpxCt . It is like - 

Default                                                  REG_SZ                              (value not set)

EnablePlainTextPassword                     REG_DWORD                     0x00000000 ( 0 )

EnableSecuritySignature                       REG_DWORD                     0x00000001 ( 1 )

Otherdomain                                        REG_MULTI_SZ                    

RequireSecuritySignature                     REG_DWORD                     0x00000000 ( 0 )

ServiceDll                                              REG_EXPAND_SZ               %SystemRoot%System32\wkssvc.dll

ServiceDllUnloadOnShop                     REG_DWORD                     0x00000001 ( 1 )

I am not  an expert , so I need your help to solve this problem .

Moved from Community Participation Center


 

Question Info


Last updated May 8, 2020 Views 2,246 Applies to:

Related Forums


trying to open " http://www.wbgdrb.applythrunet.co.in/ "

In my case I first got a 403 Forbidden response.  So then I closed that tab (Ctrl-w) and re-opened it (Ctrl-Shift-T) and strangely had no problem.  I was actually going to see where you were getting your KB article reference from.   ; )

But essentially all I get from that is a link to here:  https://www.iis.net/

FYI

Robert Aldwinckle
---

Did this solve your problem?

Sorry this didn't help.

Great! Thanks for marking this as the answer.

How satisfied are you with this reply?

Thanks for your feedback, it helps us improve the site.

How satisfied are you with this response?

Thanks for your feedback.